Analyzing Leak Detection Methods for Aluminum Cast Components in Automotive Manufacturing Processes
DOI:
https://doi.org/10.59188/eduvest.v4i4.1200Keywords:
Air Leak Tester, Waterleak, Cosmo, Aluminium Casting, LeakAbstract
This study was conducted to detect leaks in aluminum casting components in the automotive manufacturing process, which is a significant issue because it can affect vehicle safety. The method used in this study is the Cosmo Air Leak Tester for leak testing using air pressure and differential methods, as well as bubble test testing as an alternative method. The results of the study show that the air leak tester machine has stable values but cannot detect leaks caused by deformation. Changes in parameters on the Cosmo Air Leak Tester do not significantly affect bubble detection. On the other hand, the water leak method proved effective in detecting early leaks with the appearance of bubbles in products experiencing deformation up to 40 microns
References
Ardi, S., & Setyowati, S. (n.d.). Desain Sistem Kendali Mesin Penguji Kebocoran Udara Menggunakan Sistem Kendali Plc Omron Cj2m di Hvac (Heating, Ventilating, And Air Conditioning). Jurnal Teknik Mesin Mercu Buana, 5(4), 146–151.
Bhosale, R. S., Kumbhar, P. P., Mahajan, K. S., Yachkal, A. K., & Katarkar, A. (2017). Study on leak testing methods. IJSRD-International Journal for Scientific Research and Development, 1618–1621.
Deshmane, V., Sisode, R., Patil, A., Ghuge, S., & Vitnor, S. K. (2021). Radiator and Evaporator Leak Testing Machine. Www.Ijariie.Com527.
Horváth, R., Réger, M., & Oláh, F. (2022). Characterisation of defects in die cast aluminium parts. IOP Conference Series: Materials Science and Engineering, 1246(1), 12016.
Https://www.cosmo-k.co.jp/. (n.d.). Manual Book & Katalog Cosmo Air Leak Tester. https://www.cosmo-k.co.jp/
Https://www.keyence.co.id/. (n.d.). Manual Book & Katalog Keyence Safety Sensor.
Kala, S., Jadhav, A., Rohit Jadhav, A., & Professor, A. (2022). Study Of various Leakage Testing Machine and Defects, 4, 1802. International Journal of Advances in Engineering and Management (IJAEM), 4, 1802.
Kelkar, R., Sabale, P., Shinde, N., Tade, S. L., & Student, U. G. (2017). AUTOMATION OF DRY TYPE LEAK TESTING MACHINE USING PLC & HMI ©IJCES ISSN: 22316590 6 | Special Issue of OIJCRTE. In. International Journal of Computer Engineering & Science.
Kucharčík, L., Brůna, M., & Sládek, A. (2014). Influence of Chemical Composition on Porosity in Aluminium Alloys. Archives of Foundry Engineering, 14(2), 5–8.
Pop, A. B., & Tîtu, M. A. (2016). Study Regarding the Quality Assurance in Manufacturing Processes. Management of Sustainable Development, 8(2), 11.
PT.XYZ, M. S. E. (n.d.). Manual Safety Evaluation PT.XYZ.
Wiryolukito, S. (2020). ANALISIS GAGAL LEAK TEST PADA PRODUK CYLINDER HEAD TYPE-A HASIL PROSES LOW PRESSURE DIE CASTING DENGAN MATERIAL AC4B DI PT. X. Technologic Politeknik Astra, 11(2).
Published
Issue
Section
License
Copyright (c) 2024 Abdur Rohman HM, Noval Lilansa, Ivan Tovani
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
